|
|
||||||||||||||||||||||||||||||||||||||||||||||
 |
|
|
|
||||||||||||||||||||||||||
| |
 |
|
|
||||||||||||||||||||||||||
GT1575 Service Duty Anti Slip Coating for Concrete Features
I. Anti-Slip Concrete Coating - GT1575
GT1575 is designed for the most demanding installations. It was developed for heavy abuse in the transportation service industry. GT1575 provides "peak" performance with a formulation that cures to an anti-slip profile. GT1575 Anti-Slip Concrete Coating provides excellent fuel and chemical resistance, impact resistance, and good color stability.
II. GT1575 Uses
The zero VOC formulation eliminates flammable vapors, making it perfect for use in areas requiring safer footing and traction for rolling equipment. GT1575 is ideal for diesel fueling areas for tractor-trailers and for automobile fueling areas.
III. GT1575 Product Data
IV. GT1575 Standard ColorsTile Red, Black, Deck Gray, Silver Gray, Tan, Safety Yellow. Custom colors are available and subject to minimum order requirements. V. Chemical ResistanceGT1575 is fire retardant in its cured state. GT1575 is resistant to acids, alkalis, solvents, grease, oil, salt water, detergents, alcohol, gasoline, jet fuels, and many other hydraulic fluids. Refer to Grip-Tek Chemical Resistance Table for detailed information. VI. GT1575 Installation ProcedureGT1575 can be applied to any clean, dry surface. Remove all paint, construction contaminants, rust, and mill scale from metal or concrete surfaces by steel shot blasting to SSPC-SP10 profile or by scarifying where necessary. See Surface Preparation Guidelines. Pre-mix Component A with a mechanical mixer making sure that any settlement has been re-dispersed. Apply only when air and surface temperatures are between 50º and 100º F and surface is at least 5º above the dew point. Depending upon substrate, use recommended GRiP-TEK primer. Pour all contents of GT1575 Hardener (Component B) into Component A. Mix thoroughly for 3 minutes until Hardener (Component B) is totally incorporated. Pour all mixed contents of GT1575 on the surface in a ribbon 6 inches wide. Use a Grip-Tek phenolic core roller. Install material by rolling in one direction only. Pull material toward you in slow straight strokes with moderate pressure. DO NOT OVER ROLL. Do not thin material. Allow to cure. Curing time will be affected by low temperatures and high humidity. VII. Concrete Surface MaintenanceMaintain a clean surface to ensure that the anti-slip safety performance of GT1575 be maximized. CRS recommends using a non-ionic, free-rinsing detergent using a scrub brush to remove contaminants. Collect all fuel and cleaner in CRS Bio-Sorb and place in container with CRS Microbes. Rinse with clean water and allow to dry. Periodic clean up is necessary to prevent fuel build up and run off into surface water. VIII. Personal ProtectionEYE PROTECTION: All personnel should be required to wear Safety goggles In case of skin contact, wash thoroughly with soap and water. Remove and discard contaminated clothing. If skin irritation occurs, contact a physician immediately. Maintain a portable eye wash fountain or a clean source of potable water in the immediate work area. In case of eye contact, flush with water for a minimum of 15 minutes and seek aid at a medical center for treatment IX. Safety and HandlingEYE PROTECTION: All personnel should be required to wear Safety goggles In case of skin contact, wash thoroughly with soap and water. Remove and discard contaminated clothing. If skin irritation occurs, contact a physician immediately. Maintain a portable eye wash fountain or a clean source of potable water in the immediate work area. In case of eye contact, flush with water for a minimum of 15 minutes and seek aid at a medical center for treatment
The information presented herein is believed to be accurate and is presented in good faith for the benefit of the customer. CR SOLUTIONS, INC. however, expressly declares that there is no guarantee of result to be obtained by the Buyer. LIMITED WARRANTY: CR SOLUTIONS, Inc. WARRANTS TO THE ORIGINAL PURCHASER OF ITS PRODUCTS THAT SUCH PRODUCTS MEET THE SPECIFICATIONS CONTAINED HEREIN. NO WARRANTY, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR SUITABLILITY FOR A PARTICULAR PURPOSE AND/OR ANY OTHER WARRANTY IS GIVEN. The obligation of CRS under this warranty is limited to the replacement of any product which we sell, which may be proven detective under normal use and service within one year of the date of sale. IN NO EVENT SHALL CR SOLUTIONS, INC., BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES.
Concrete Remediation Solutions - Product List
|
|||||||||||||||||||||||||||||
|
water soluble solution to remove oil and grease from concrete
solution to "eat" removed wastes
|
organic blend to control pH & assist microbial action
biodegradable pellets to absorb wastes
|
GT1575 is a 100% reactive, solvent-free, two component epoxy anti-slip coating for concrete, metal, and wood surfaces. 
GT1575 is designed to be installed in areas that are fuel sensitive.